| Prices are in US $ 
| |  | Mask, Snorkel Combos | Home » » 1700 Case with foam | | | | | | | Description: | | O-ring seal. Pressure Equalization Valve. Strong polyurethane wheels with stainless steel bearings. 3-piece foam set. | | | Features: | |
• Exterior Dimensions: 38.12" x 16.00" x 6.12" (96.8 x 40.6 x 15.5 cm)
• Interior Dimensions: 35.75" x 13.50" x 5.25" (90.8 x 34.3 x 13.3 cm)
• Watertight, crushproof, and dust proof
• Unconditional Lifetime Guarantee of Excellence
• Open cell core with solid wall design - strong, light weight
| | | Product Details: | | | Product Length:
| 16.0 inches | | Product Width:
| 6.12 inches | | Product Height:
| 38.12 inches | | Product Weight:
| 20.0 pounds | | Package Length:
| 39.0 inches | | Package Width:
| 18.5 inches | | Package Height:
| 6.5 inches | | Package Weight:
| 18.75 pounds | | Average Customer Rating:
|  based on 6 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
Write an online review and share your thoughts with other customers.
Overkill comes at a weight expenseSep 07, 2010
I replaced my factory supplied rifle case (for the Sig Sauer 556 Classic SWAT) with the Pelican 1700 because the original case could not fit any mounted optics. Additionally, I wanted to have a forward grip mounted and that wouldn't fit either. The 1700 fits the Sig 556, with optics and forward grip, either with the stock collapsed (barely) or with plenty of room to spare with the stock folded. To fit a folded stock, I cut partially into the top foam (about .75"). I did the same thing for the magazines. I also had room for four standard 30 round magazines, the backup diopter site, a Sig 229R .40, and three magazines for the 229.
Cutting the foam was easier than expected. I initially planned to use a hot nichrome wire to cut the foam from a stencil, but found that a serrated knife worked just fine. I followed the instructions and used chalk to outline, then cut in about 1/4" from the outline. This creates a very snug fit. In the end this was exactly what I was looking for to carry my gear to the range. It's overkill in that I'm sure I could drop the loaded case from a three story building and the gear would survive (and I really don't need that). All that protection adds to the weight, and while I knew it would be heavy, it's a lot heavier than the no frills factory case.
Only things I would change is the non-collapsible side handle and the fact that it won't stand up on the narrow edge with the wheels (minor issues). Here's a tip when arranging your gear: consider the weight distribution so the case is balanced from the handle.
1 of 1 found the following review helpful:
Typical Pelican qualityMay 10, 2010
This is like every other Pelican product I have seen--excellant. The only slight issue is that the main handle doesn't fold down, technically making the case exceed airline luggage size restrictions. Southwest didn't seem to care, although I was prepared to cut that handle off to avoid the $50.00 oversize penalty. A great case.
Great CaseApr 19, 2010
I've had one of these for about 7 years now, and I've all sorts of guns in it. Interchangeable foam sections make it possible to have custom inserts for different gun and accessory combinations, and then just switch them out depending on which ones you want to take along each time. A very handy feature.
The case is also very rugged. It feels like it could take a pretty good beating and absorb all the actual abuse, while keeping your contents in good condition.
Another really nice feature is the clasp guards. These are the small plastic protrusions that run along side of the plastic clasps that hold the case closed. The guards keep things from randomly getting hooked on the clasp and accidentally popping it loose/open. It all works together to make better security while transporting.
One end has hard rubber wheels and the other end has a handle so the case can be wheeled along like any other over-night bag you see at the airport, greatly cutting down you load weight. That's a really nice feature if you have to haul it pretty far.
Anyway, this thing is pretty much an industrial quality unit and similar to other custom cases that we haul computers and expensive test equipment around NASA with. I'd give it 6 stars if that were possible.
3 of 3 found the following review helpful:
 Interior dimensionsMar 04, 2010
This is one sturdy little puppy--you can stand on it. But be warned: the interior dimensions are 36" x 24" x 4.5", and it's not all usable. Inside the case you will find two 1.5" slabs of foam in the bottom of the case, and another single piece in the top. You are supposed to trace lines around your equipment on one of the bottom pieces--leaving at least an inch of foam along the sides. Then cut out the holes you traced with an electric carving knife. That means the depth of the cutout is 1.5"--the thickness of one piece of foam. For me, 1.5 inches is not enough to hold my scoped M4 with a laser on a side rail. Even cutting into the top and bottom pieces (which you are not supposed to do) will not give me enough room. So I'll have to dismount the laser for transport, which is a real pain.
Pros:
Really, really tough.
Reinforced lock holes
Wheels
Watertight (claimed) with automatic pressure equalization
Cons:
Heavy!
Interior is small for exterior size
Great case - solidFeb 01, 2010
Great case. Solidly put togethter. I expect it will take some substantial abuse.
| | |
|
